Instructions for Installation and Use
Electric Hob
Model E302X
Introduction
Your new hob is guaranteed* and will give lasting service. This guarantee is only applicable if the appliance has been
installed in accordance with the installation instructions detailed in this booklet.
To help make best use of your cooking equipment, please read this booklet carefully.
The hob is designed specifically for domestic use and responsibility will not be accepted for use in any other installation.
When first using the hob ensure that the room is well ventilated (eg. open a window or use an extractor fan) and that
persons who may be sensitive to the odour avoid any fumes. It is suggested that any pets be removed from the room
until the odour has ceased. This odour is due to temporary finish on elements.
* The guarantee is subject to the provisions that the appliance:
(a) Has been used solely in accordance with this booklet.
(b) Has been properly connected to a suitable supply voltage as stated on the rating plate, attached to the
appliance.
(c) Has not been subjected to misuse or accident or been modified or repaired by any person other than the
manufacturers authorised employee or agent.
(d) Has been correctly installed.
This appliance conforms with the following European Economic Community directives
-
-
-
73/23/EEC of 19/02/73 (Low Voltage) and subsequent modifications.
89/336/EEC of 03/05/89 (Electromagnetic Compatibility) and subsequent modifications.
93/68/EEC of 22/07/93 and subsequent modifications.
3
For Your Safety
When used properly your appliance is completely safe but as with any electrical product there are certain
precautions that must be observed.
PLEASE READ THE BELOW PRECAUTIONS BEFORE USING YOUR APPLIANCE.
To maintain the efficiency and safety of this appliance, we recommend you do the following:
- only call the Service Centres authorised by the manufacturer.
- always use genuine spare parts.
ALWAYS:
NEVER:
- make sure you remove all packaging and dispose of safely. - attempt to install or repair the appliance without the
- check the soundness of the appliance after it has been assistance of qualified personnel.
unpacked.
- store items above the appliance that children may attempt
- make sure you understand the controls before using the to reach.
appliance.
- heat up unopened food containers, as pressure can build
up causing the container to burst.
- keep children away from the appliance during use.
- take care to avoid heat/steam burns when operating the - use the appliance to heat up anything other than food.
controls. - use the appliance as a room heater.
- make sure the controls are turned off when you have finished - dry any items on the hob.
cooking and when not in use.
- install the appliance next to curtains or other soft furnishings.
- disconnect from the power supply, and allow to cool, before - allow children to play with or tamper with the controls.
cleaning or performing maintenance.
- refer servicing to a qualified appliance service engineer.
- leave children unsupervised where cooking appliances are
installed as all the cooking surfaces get hot during and after
- keep the hob clean as a build up of grease or fat from use.
cooking can cause a fire.
- store chemicals, foodstuffs or pressurised containers in or
- follow the basic principles of food handling and hygiene to on the appliance, or in cabinets immediately above or next
prevent the possibility of bacterial growth.
to the appliance.
- dry food thoroughly before frying and lower it slowly into the - use flammable or plastic items on or near the hob.
hot oil or fat. Frozen food in particular, will cause froth and - use adapters, multiple sockets and/or extension leads.
spitting if added too quickly.
- keep outside of pans clean and free from streaks of oil or DO NOT LEAVE UNATTENDED WHILE COOKING.
fat. - fry too much food at a time, especially frozen food. This
- fill a deep fat frying pan more than 1/3 full of oil, or use a lid.
- place pans centrally over the hotplates making sure only lowers the temperature or the oil or fat too much, resulting
handles are kept away from the edge of the hob and cannot in greasy food.
be heated by other hotplates/pans.
- keep any ventilation slots clear of obstructions.
- pull on the appliance or the supply cable to unplug it from
the electrical outlet.
- allow power cables of other appliances to come into contact
with hot parts of this appliance.
- expose the appliance to atmospheric agents, such as
rain or sunlight.
- operate the appliance with wet hands.
- operate the appliance when barefoot.
- allow anyone to sit or stand on any part of the appliance.
- use misshapen pans which may be unstable.
- use fish kettles or large preserving pans across two
hotplates.
- leave anything on the hob surface when unattended and
not in use.
SAFETY ADVICE
IMPORTANT - As with any cooking appliance there could be some fire risk attached to the heating of oil, particularly for
deep fat frying. Cooking utensils containing oil must not be left unattended (eg. to answer the telephone) on or in close
proximity to the cooking areas.
IN THE EVENT OF A CHIP PAN OR ANY OTHER PAN FIRE:
1. Turn off the hotplates.
2. Cover the pan with a fire blanket or damp cloth, this will smother the flames and extinguish the fire.
3. Leave the pan to cool for at least 60 minutes before moving it. Injuries are often caused by picking up a hot pan and
rushing outside with it.
NEVER USE A FIRE EXTINGUISHER TO PUT OUT A PAN FIRE as the force of the extinguisher is likely to tip the pan
over. Never use water to extinguish oil or fat fires.
4
Know your Hob
C
1 and 2
Cooking areas
1A and 2B Controls
A
B
How To Use Your Hob
To turn on a cooking area and increase its power
level, select the desired cooking area. Then turn the
corresponding control to the required position. The higher the
number, the greater the power.
Quick /
Automatic
Heat
Normal
1
2
3
4
5
6
1 - 2
Least Hot
Controls for "Quick/Normal" plates turn in both directions to
settings numbered 0 - 6.
3 - 4
Only turn controls for "Automatic" plates clockwise to
settings numberes 0 - 12.
5 - 6
7 - 8
9 - 10
11 - 12
To turn off the cooking area, return the control to 0 and
the cooking area is turned off.
Hottest
Pilot light
The pilot light will come on when cooking areas are switched
on.
Even after a cooking area is turned off some types of pilot
light stay on to show that the cooking area is still hot. The
pilot light warns you there is still the risk of injury by burning.
5
Practical Advice
Choice of utensils:
Every Electric Hob deserves the right choice of utensils. We
recommend for optimum performance the use of good quality
utensils.
PANS SHOULD NOT:
•
•
•
•
Be concave (bowed in).
Be convex (bowed out).
Be rimmed.
Be deeply ridged.
BUT SHOULD BE ESSENTIALLY FLAT
Always
Never
•
Use good quality flat-based cookware on all electric heat
sources.
•
•
Use gauze, metal pan diffusers, asbestos mats and
stands eg. wok stands - they can cause overheating.
Use utensils with skirts or rims eg. buckets and some
kettles.
•
•
•
•
Place pans centrally on the hotplate.
Ensure pans have clean, dry bases before use.
Ensure pans match the size of the heating area.
Remember good quality pans retain heat well, so
generally only a low or medium heat is necessary.
Ensure pan handles are positioned safely and away
from heat sources.
Lift pans, do not drag.
Use pan lids, except when frying.
Deal with spillage immediately, but with care.
•
•
•
•
•
Use badly dented or distorted pans.
Leave an element on when not cooking.
Cook food directly on the hotplate.
Drag or slide utensils across the hotplate.
Place large preserving pans or fish kettles across two
hotplates.
•
•
•
•
•
•
Place plastic vessels or utensils on a hot hob.
Use the hob as an area for storage.
6
Care and Cleaning
The Hotplates
Before cleaning or performing maintenance on your hob,
disconnect it from the power supply. Check that all controls
are in the OFF position before reconnecting.
Clean with a cloth wrung out in warm water. Then rub a litlle
cooking oil into the hotplates while they are still warm to
condition the surface. Ensure care is taken as the hotplates
will be warm.
Clean spills immediately.
Enamelled, Stainless Steel and Glass parts
Wipe with a cloth wrung out in warm soapy water followed
by a wipe with a cloth wrung out in clean water and then
dry with a soft clean cloth.
NEVER USE: Washing powder, harch abrasive,
scouring pads, aerosol cleaners or oven chemical
clearners of any kind.
Cleaning materials to avoid
Control Knobs
•
Household abrasive powders, eg. Vim.
Wipe over the knobs with a soft cloth wrung out in warm
soapy water or mild non-abrasive. Then, after wiping with a
cloth wrung out in clear water, dry with a soft clean cloth.
•
Oven chemical cleaners, aerosols and oven pads -
Caustic cleaners such as these will etch the surface and
attack the metal frame.
•
Bath and sink cleaners may mark the surface.
Painted Metal Surround Trim
Wipe over with a cloth wrung out in warm soapy water
only. DO NOT USE ABRASIVES.
Troubleshooting
Before calling service for assistance, check through the
following list, there may be nothing wrong.
If, despite all of these checks, the hob does not function
properly and problem persists, call Hotpoint Service (see
KEY CONTACTS, back page), informing them of:
- The type of problem.
- The abbreviation used to identify the model (Mod. ...) as
indicated on the warranty.
Nothing works.
Check to make sure that:
•
the mains wall switch is switched on.
If a control is on, the corresponding pilot light will
come on.
IMPORTANT:
Hotplates are slow to boil or will not simmer.
Check to make sure that:
Never call upon technicians not authorized by the
manufacturer, and refuse to accept spare parts that are not
original.
•
Your pans conform with the recommendations detailed
in this book.
7
Installation
These instructions are intended for the qualified technician
installing the appliance in order to insure that the installation,
adjustments and maintenance procedures are performed
correctly and comply with the regulations currently in effect.
Important: the hob must be disconnected from the
power supply before making any adjustments or
performing any maintenance, etc.
Installing built-in hobs
The hob is a type Y appliance, therefore, the hob can be
installed alongside of cabinets which are higher than the
surface of the worktop. The following precautionary measures
should be observed in order to ensure proper installation:
a) Hoods must be installed in compliance with the required
specifications contained in the instruction manual for the
hood itself.
These measurements must absolutely be observed in
so far as improper installation can cause the surrounding
surface areas to overheat. It is recommended that the
hob be installed at a distance of at least 55 mm from the
back wall or other vertical surfaces to ensure that the air
circulates properly over the cooking area and to avoid
overheating the surrounding surfaces. A seal or gasket
is provided with the hob, make sure that it adheres
properly to the bottom part of the frame of the hob.
The seal must fit properly around the entire hob frame
and especially along the corners in order to create a
seal between the work top and the hob itself so as
to prevent spills or splashes from leaking into the
cabinet below.
b) The dimensions and the position of the hole are shown
below:
The hob must be fixed into the worktop using the fixing clamps
- see diagram.
Very important
It is essential to install the hob on a totally flat surface. Any
damage caused by incorrect fitting may alter the characteristics
or impair performance.
Insert the hob into the hole, pressing firmly around the frame
to make it adhere to the counter top.
Note: If the hob is installed above a built-in oven, it is
preferable that the oven be installed in such a way that it is
set on two strips of wood; if the oven is installed on a
continuous base, there must be an opening in the back of
at least 45 x 560 mm.
The built-in oven must be equipped with a forced air
cooling system.
8
Electrical Connection
Electrical Connection
Connecting the supply cord to the electrical mains:
THIS APPLIANCE MUST BE EARTHED.
The installation procedure must be carried out by a qualified
electrician.
The electrical safety of this appliance is guaranteed only if
the appliance is correctly earthed in compliance with the
standards of electrical safety.
The hob must be connected to a double pole mains switch
which must be installed between the appliance and the
mains. The double pole mains switch must have a minimum
of 3mm of space between the contacts, be sized to the
load and comply with current regulations (the switch must
not be able to disconnect the earth conductor).
The manufacturer can under no circumstances be considered
responsible for any damage that might occur due to incorrect
earthing of the hob.
The supply cord should conform to BS6004 conductor size
4mm and must be positioned so that no part of it reaches
a temperature of 50°C higher than room temperature.
2
Before making the connection, make sure that:
•
•
•
•
the limiter switch (fuse) and the residual wiring can support
the appliance load (see the rating plate, below).
the mains system is properly earthed in compliance with
current regulations and provisions.
there is easy access to the socket or the double pole
mains switch after the appliance is installed.
the isolation switch must not be positioned directly above
the hob.
IMPORTANT:
If the hob is installed above a built-in oven, the electrical
connection for the hob must be independent of that for the
oven, both for safety reasons and to facilitate the removal of
the oven for maintenance, repair etc.
HOTPLATES:
Normal Hotplate O145
Normal Hotplate O180
Quick Hoplate O145
Quick Hotplate O180
1000W
1500W
1500W
2000W
Red Spot
Red Spot
Automatic Hotplate O145 1500W
Automatic Hotplate O180 2000W
9
After Sales Service
"No company is better positioned to offer an after sales service on a
Hotpoint appliance than us - the manufacturer"
As part of our commitment to you, all Hotpoint appliances have the added benefit of a fully inclusive parts
and labour guarantee for the first 12 months. In addition to this you also have the advantage of free
replacement parts for the first 5 years when fitted by a Hotpoint
engineer. When the 12 months parts and labour guarantee expires we offer the following after sales
service options:
Repair Service and Information Help Desk
UK: 08709 066066
Republic of Ireland: 1850 302 200
Note: Our operators will require the Model number and the Serial number of your appliance
Available 364 days a year with a fast, effective and value for money service. We have the largest white
goods repair service in the UK with over 1200 of our own fully trained engineers. All repairs include a parts
and labour guarantee for 12 months from the date of the repair.
If you require any information or have any questions about your appliance, our operators are on hand with
help and advice.
All this ensures that you will receive the best available after sales service possible.
Extended Warranties
UK: 08709 088 088
Republic of Ireland: 1850 502 200
Whether you have just one or a number of Hotpoint appliances in your kitchen, we offer two service cover
plans to give you total peace of mind.
ꢀ Repair Protection Plan
-
FREE service repairs for a single Hotpoint appliance during the period
of cover.
ꢀ Kitchen Cover
-
FREE service repairs for all your Hotpoint appliances less than 8
years old.
Genuine Parts and AccessoriesUK: 08709 077 077
Republic of Ireland: (01) 842 6836
A wide range of genuine parts and accessories are available from our hotline or through our web site.
Genuine parts and accessories, extended warranties and service repairs are all
available on our web-site at:
GB
10
Guarantee
"Satisfaction guaranteed or your money back"
We give you a unique 'satisfaction guaranteed' promise - valid for 90 days - after you have
purchased your Hotpoint appliance. If there is a technical problem simply call Hotpoint Repair service or
engineer to call. If the technical problem is not resolved under this guarantee, we will replace your
machine or, if you prefer, give you your money back.
All Hotpoint appliances carry a fully inclusive 12 month parts and labour guarantee as well as free
replacement parts for the first 5 years (except microwaves, selected integrated appliances and cooker
hoods, which have a one year guarantee) provided that they are fitted by a Hotpoint engineer.
Guarantee terms and conditions
Your guarantee is only applicable in the United Kingdom or Republic of Ireland and is subject to the
following provisions that your appliance:
ꢀ
ꢀ
Has been installed and used correctly in accordance with this instruction booklet.
Has been used solely for domestic purposes and is located on domestic premises (ie. not for
commercial or trade use).
ꢀ
ꢀ
Has been properly connected to a suitable electrical supply voltage as stated on the appliance
rating plate.
Has not been subject to misuse, accident, modified or repaired by anyone other than one of our
own service engineers.
For pre purchase information on any other Hotpoint product call: 08701 50 60 70
Recycling & Disposal Information
As part of Hotpoint's continued commitment to helping the environment, Hotpoint reserves the right to
use quality recycled components to keep down customer costs and minimise material wastage.
Please dispose of packaging and old appliances carefully.
To minimise risk of injury to children, remove the plug and cut mains cable off flush with the appliance.
Dispose of these parts separately to ensure that the appliance can no longer be plugged into a mains
socket.
GB
11
Key Contacts
After Sales Service
Over 1200 trained specialists, directly employed by us, ensure that you can have complete
confidence in both the appliances and services we offer.
Repair Service and Information Desk
UK: 08709 066 066
(Open 8 to 8 Mon - Fri, 8 to 6 Sat, 10 to 4 Sun & Bank Holidays)
Republic of Ireland: 1850 302 200
Note: Our operators will require the following information:
Model number:
Serial number:
Extended Warranties
UK: 08709 088 088
(Open 8 to 8 Mon - Sun)
Republic of Ireland: 1850 502 200
Genuine Parts and Accessories
UK: 08709 077 077
(Open 8-30 to 5-30 Mon - Fri & 9 to 12 Sat)
Republic of Ireland: (01) 842 6836
General Domestic Appliances Limited, Morley Way, Peterborough, PE2 9JB.
February 2003 Part no. FP165 - 01
COD. 1.002.63.0
|